Welcome to download the newest Pass4itsure 700-501 dumps: http://www.pass4itsure.com/700-501.html
Nowadays,Flydumps has published the newest Cisco 642-052 exam dumps with free vce test software and pdf dumps,and the latest Cisco 642-052 question answers ensure you 100% pass and money bcak guarantee.
QUESTION 96
How many network module slots does the Cisco 3745 have?
A. 1
B. 2
C. 3
D. 4
Correct Answer: D QUESTION 97
As a contractor, you have been asked by a local telco to assist in the install of CPE for their ADSL network. They are using Cisco DSLAMs in their core network and want to use Cisco CPE for their customers.They inform you that they want you to select from several routers depending on customer needs as they have several levels of service. At your first customer location, the customer informs you that they want to use the router to make a direct, continuous, encrypted connection to their corporate headquarters with no split tunneling.Which Cisco ADSL router should you install?
A. Cisco 831
B. Cisco 837
C. Cisco SOHO 91
D. Cisco SOHO 97
Correct Answer: B QUESTION 98
Which parameter will be used to determine when to disconnect an idle established DDR call, when the line is needed to place a DDR call to a different destination?
A. The time specified by dialer idle-timeout.
B. The time specified by dialer fast-idle.
C. The value configured by dialer load-threshold.
D. The presence of interesting traffic designated for a different destination will force an immediate disconnect.
Correct Answer: B QUESTION 99
A customer needs a router that will provide 2 WIC slots, an internal VPN card slot, support for two Ethernets of at least 10baseT, and a redundant power supply. Which router is the lowest cost solution?
A. Cisco 1751
B. Cisco 1760
C. Cisco 2611XM
D. Cisco 2621XM
Correct Answer: C
QUESTION 100
Which statement about configuring NAT for TCP load distribution is true?
A. It is enabled by mapping multiple outside addresses to an inside address.
B. It is enabled with the type rotary parameter on the ip nat pool command.
C. It is configured with the overload parameter on the ip nat inside command.
D. It requires an access list that permits an outside address to a group of inside local addresses.
Correct Answer: B
QUESTION 101
When building an IP multicast domain using PIM which mode assumes that other routers do not want to forward multicast packets for the group?
A. PIM-DM
B. PIM-SM
C. PIM-RP
D. CGMP
E. IGMP snooping
Correct Answer: B
QUESTION 102
EZ VPN is configured in Client mode with auto connection. What is the behavior of the router when the VPN connection is down but the router is still operational and attached to the Internet?
A. The router has no connection since the VPN is down.
B. The router will permit Internet access but continues to attempt to attach to the VPN.
C. The user cannot get out to the Internet because the router continues to attempt to attach to the VPN.
D. The router works normally and the VPN connection is dormant until the user initiates the VPN again.
Correct Answer: C
QUESTION 103
Which three are responsibilities of IKE in the IPsec protocol? (Choose three)
A. negotiating protocol parameters
B. packet encryption
C. exchanging public keys
D. integrity checking using hashes
E. authenticating both sides of a connection
F. implementing tunnel mode
Correct Answer: ACE
QUESTION 104
What is a characteristic of a static VLAN membership assignment?
A. VMPS server lookup
B. easy to configure
C. ease of adds, moves, and changes
D. based on MAC address of the connected device
Correct Answer: B QUESTION 105
What are three features of the VAM? (Choose three.)
A. compression
B. key generation
C. software assisted encryption
D. hardware assisted encryption
Correct Answer: ABD QUESTION 106
You have been asked by a client to help company employees connect with an ISP so that they can gain access to the Internet. The employees will use VPN software on their PCs to access the corporate network through the Internet. No cable or DSL is available so you must use ISDN.The telco does NOT supply NT1s, there will be two PCs connecting and a printer at each location, and each location will have an analog fax machine. Which Cisco 800 series router should you recommend?
A. Cisco 801
B. Cisco 802
C. Cisco 803
D. Cisco 804
Correct Answer: D QUESTION 107
What is the default IP address for the CRWS tool as accessed from the inside port of the Cisco SOHO or Cisco 800 series routers?
A. 10.0.0.1
B. 10.10.0.1
C. 10.10.10.1
D. 10.10.10.10
Correct Answer: C QUESTION 108
Which statement describes the term “multilayer switching”?
A. switches that operate at the access, distribution, and core layer of the design model
B. an OSI Layer 1 and 2 bridging technique
C. a technique to provide hardware switching of Layer 3 unicast packets
D. a flow-based Layer 3 packet routing methodology
Correct Answer: C QUESTION 109
Which statement describes a feature of a Switch Port Analyzer (SPAN) session?
A. affects switching traffic on source ports
B. associates a source interface with multiple destination interfaces
C. eliminates multiple copies of packets
D. associates multiple source interfaces with a single destination interface Correct Answer: D
QUESTION 110
Which statement is true about the STP Path Cost on a particular port?
A. It is known only to the local switch where the port resides.
B. It can be modified to help determine Root Bridge selection.
C. Modifying it can cause TCN BPDU to be sent to the Root Bridge.
D. When increased, it can provide higher bandwidth to a connecting port.
Correct Answer: A QUESTION 111
Which two routers support the use of Etherswitch modules and provide power to IP phones with the use of an external power supply? (Choose two.)
A. Cisco 2650
B. Cisco 2691
C. Cisco 3725
D. Cisco 3745
Correct Answer: AB QUESTION 112
Which two routers can act as an EZ VPN Remote client? (Choose two.)
A. Cisco 801
B. Cisco 806
C. Cisco 1710
D. Cisco 2610
Correct Answer: BC QUESTION 113
What are the optional components of the 36 port HDSM?
A. Power Daughter Card and one GE-TX port
B. Power Daughter Card and two GE-TX ports
C. Dual Power Daughter Card and one GE-TX port
D. Dual Power Daughter Card and two GE-TX ports
Correct Answer: B QUESTION 114
Which Cisco router is the highest performing 1 RU high router in the industry?
A. 1760
B. 2621
C. 3620
D. 7400
Correct Answer: D QUESTION 115
Which Quality of Service technology classifies traffic entering a queue based on dynamically observed traffic flows?
A. FIFO
B. WFQ
C. Custom Queuing
D. Priority Queuing
Correct Answer: B
QUESTION 116
A company has unique dial requirements for each branch site that communicates with a central site router. Which two commands permit multiple physical interfaces on a central router to be shared by multiple remote sites while retaining their unique site requirements? (Choose two.)
A. dialer pool
B. dialer-list
C. dialer-group
D. dialer hunt-group
E. dialer pool-member
Correct Answer: AE
QUESTION 117
You have been asked to provide a router with thirty 10/100 Ethernet interfaces and room for more for future growth. The router must also provide security in the form of firewalls for each Ethernet interface.Which router should you install?
A. Cisco 7206
B. Cisco 7304
C. Cisco 7513
D. Cisco 7603
Correct Answer: D
QUESTION 118
What would the following command set on a router? router(config)#interface group-async 1 router(config)#group-range 1 7
A. assigns asynchronous interfaces 1 through 7 to a single master interface
B. assigns dialer privileges to interfaces async 1 through 7
C. creates virtual asynchronous interfaces 1 through 7
D. creates virtual TTY interfaces 1 through 7
E. trunks asynchronous interfaces to increase modem bandwidth
F. creates a modem pool on interfaces 1 through 7
Correct Answer: A
QUESTION 119
Which router command is used to reverse telnet to a modem locally connected to line 8?
A. telnet 10.1.1.1 1008
B. telnet 10.1.1.1 2008
C. telnet 10.1.1.1 8
D. telnet 8 10.1.1.1
Correct Answer: B
QUESTION 120
You need a router that can provide WAN broadband Ethernet connectivity at 10baseT and a LAN connection at 10/100 including 802.1q trunking. It must provide an ADSL connection for backup should the Ethernet WAN interface fail.Which Cisco router is the lowest cost solution?
A. Cisco 1721
B. Cisco 1760
C. Cisco 2611XM
D. Cisco 2621XM
Correct Answer: A
QUESTION 121
What are the market drivers for WAN products?
A. speed, cost, user demands
B. cost, user demands, availability
C. user demands, scalability, availability
D. competition, user demands, new and improved products and services
Correct Answer: D
QUESTION 122
What Cisco switch command will map VLANs 10 to 20 to MST instance 1?
A. Switch(config)#vlan 10-20 instance 1
B. Switch(config-mst)#vlan 10-20 instance 1
C. Switch(config)#instance 1 vlan 10-20
D. Switch(config-mst)#instance 1 vlan 10-20
Correct Answer: D
QUESTION 123
Which three of the following router IOS commands defines “interesting” traffic for only one host using dial on demand routing (DDR)? (Choose three.)
A. RTA(config)#dialer-list 1 protocol ip permit 10.1.1.1
B. RTA(config)#access-list 2 permit host 192.168.1.12
C. RTA(config-if)#dialer-group 1
D. RTA(config)#dialer-group 2
E. RTA(config)#dialer-list 1 protocol ip list 2
F. RTA(config-if)#dialer-list 2 protocol ip permit
Correct Answer: BCE
QUESTION 124
Which command is used to specify protocols that are allowed for incoming asynchronous dial-up connections?
A. modem inout
B. async-group in
C. access-group async
D. transport input
Correct Answer: D
QUESTION 125
The Cisco 7400 uses the same processor as which 7200 engine?
A. NSE 1
B. NSE 3
C. NPE 225
D. NPE 300
E. NPE 400
Correct Answer: A QUESTION 126
Which statements are true about the data-link connection identifier (DLCI)? (Choose two.)
A. DLCI numbers need to be identical on all DTE devices.
B. DLCI numbers have local significance.
C. DLCI is assigned by Network Administrator.
D. DLCI is assigned by the Frame Relay service provider.
Correct Answer: BD QUESTION 127
The telecommunications sector is now highly competitive. New carriers are _____.
A. using cable to compete with DSL
B. creating applications and reporting capabilities to compete with incumbent carriers
C. using wireless to provide speed and are creating new applications they believe will satisfy user demand
D. creating enhanced services to compete with incumbents, and new carriers are creating infrastructure so they do not need to outsource to existing operators
Correct Answer: D QUESTION 128
Drag Drop question
A.
B.
C.
D.
Correct Answer: QUESTION 129
What command will specify IEEE 802.1Q as the encapsulation method for a trunked port on a Cisco IOS switch?
A. Switch(config-if)#switchport trunk encapsulation dot1q
B. Switch(config-if)#switchport trunk encapsulation isl
C. Switch(config-if)#switchport encapsulation dot1q
D. Switch(config)#switchport 0/1 trunk encapsulation isl
Correct Answer: A
QUESTION 130
Using the Cisco three level design strategy, how many tiers are present in small campus networks?
A. 1
B. 2
C. 3
D. 4
E. 5
Correct Answer: B
QUESTION 131
Which IOS configuration command is used to define interesting packets to trigger a DDR call?
A. dialer-list
B. dialer-group
C. dialer in-band
D. dialer rotary-group
Correct Answer: A
QUESTION 132
The console port on the Cisco 6513 switch allows which type of management?
A. physical management of the switch
B. logical management of the switch
C. in-band management of the switch
D. out-of-band management of the switch
Correct Answer: D
QUESTION 133
You are using the CRWS tool to set up EZ VPN. Which type of connection type for the VPN will be created?
A. manual
B. automatic
C. temporary
D. permanent
Correct Answer: B
QUESTION 134
Some Cisco Supervisor Engines have modular uplink ports so that a module can be selected to provide an appropriate level of bandwidth. Which two features are valid on a 2-port 1000Base SX or 1000Base LX modular uplink module? (Choose two.)
A. 10/100 Autosensing
B. Fast EtherChannel
C. ISL
D. 802.1Q/p
E. L3 rewrite
Correct Answer: CD QUESTION 135
Which of the following guidelines is not necessary when configuring dynamic VLAN membership?
A. configure VMPS server
B. turn off trunking on the port
C. turn off 802.1x port security
D. configure the spanning-tree PortFast feature
Correct Answer: D QUESTION 136
You have used CRWS to set up an auto EZ VPN connection using Client mode with PAT. Which statement is true about the connection?
A. The connection uses the IP address of the outside interface to base the PAT address on and uses all other physical interface configurations.
B. The connection ignores the physical outside address and uses addresses from the server for the both the inside and the outside addresses.
C. The connection uses the IP address of the outside interface to base the PAT address on and uses server-supplied addresses for the inside interface and workstations.
D. The connection ignores the outside IP address and uses one supplied by the server, while the inside addresses are used from the physical DHCP configuration of the client router.
Correct Answer: D QUESTION 137
At which OSI layer does Spanning Tree Protocol operate?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
Correct Answer: B QUESTION 138
Which two routers are considered adequate replacement for the Cisco 3640? (Choose two.)
A. Cisco 2650
B. Cisco 2691
C. Cisco 3725
D. Cisco 3745
Correct Answer: CD QUESTION 139
In an EZ VPN Remote client configuration it is often necessary to configure a DHCP pool on the client router. Within this pool, what DHCP pool sub-command is used to pull DNS information for the pool from an outside source when this information will not be known prior to use?
A. Import DNS
B. Import all
C. Extract DNS
D. Extract all
Correct Answer: B
QUESTION 140
Which switch command enables a trunking protocol that appends a four byte CRC to the packet?
A. Switch(config-if)#switchport trunk encapsulation dot1q
B. Switch(config-if)#switchport trunk encapsulation itef
C. Switch(config-if)#switchport trunk encapsulation fddi
D. Switch(config-if)#switchport trunk encapsulation isl
Correct Answer: D
QUESTION 141
You have just been asked by a customer to install a 160 branch Frame Relay network. You cannot put more than 8 Frame Relay connections in one port due to bandwidth requirements. You must use T1 interfaces because the connections span multiple carriers.Which two routers are most appropriately used for this application? (Choose two.)
A. Cisco 7200
B. Cisco 7300
C. Cisco 7400
D. Cisco 7500
Correct Answer: AD
QUESTION 142
From the figure, which command would enable the central router to dynamically fluctuate the rate at which it sends packets to the branch site over the Frame Relay network?
A. frame-relay traffic-rate adaptive
B. frame-relay adaptive-shaping fecn
C. frame-relay adaptive-shaping becn
D. frame-relay traffic-rate dynamic
Correct Answer: C
QUESTION 143
Which two statements about LMI autosensing are true? (Choose two.)
A. It is used to tell the router about LMI type.
B. It only works if the Frame Relay LMI type is cisco.
C. It involves sending full status requests to the Frame Relay switch.
D. It is used to automatically detect the Frame Relay CIR of each PVC.
Correct Answer: AC
Not only will you be given theoretical, but also given practical labs which will give you even more practice than before. Our site offers you a comprehensive look at the best prospects available in Cisco 642-052 exam sample questions throughout the Industry. The Cisco 642-052 exam sample questions offered by FLYDUMPS is very comprehensive and covers all exam questions that need to be covered to pass the Cisco 642-052 exam. Professionals and experts at FLYDUMPS are very dedicated and they prepare Cisco 642-052 exam sample questions with great effort. In our Cisco 642-052 exam sample questions you will the accurate and up-to-date information.
Welcome to download the newest Pass4itsure 700-501 dumps: http://www.pass4itsure.com/700-501.html