Flydumps guarantee your Cisco 642-887 exam success with our Exam Resources.Our Cisco 642-887 Flydumps are the latest and developed by experience’s IT certification Professionals working in today’s prospering companies and data centers.All our Cisco 642-887 Flydumps including Cisco 642-887 exam questions which guarantee you can 100% success Cisco 642-887 exam in your first try exam.

QUESTION 36
In which two Cisco IOS XR configuration modes can mpls ldp igp sync be configured? (Choose two.)
A. config-ldp
B. config-if
C. config-ospf-ar
D. config-ospf
E. config-isis

Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 37
On Cisco routers, which three methods can be used to map traffic into the MPLS traffic engineering tunnel? (Choose three.)
A. on-demand routing
B. static routing
C. optimized edge routing
D. policy-based routing
E. autoroute

Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 38
Which three statements are correct regarding a Cisco MPLS TE? (Choose three.)
A. A Cisco MPLS TE tunnel maps onto an LSP path.
B. Tunnels are bidrectional by default.
C. Packets that are mapped into a Cisco MPLS TE tunnel will have two labels, with the top label indicating what the tail-end router should do with the packet.
D. A tunnel that is created with a priority of 0 can pre-empt an existing tunnel with a priority of 7.
E. CBR takes into account link resource and traffic tunnel attributes.
F. RSVP is used between customer routers.

Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 39
On a Cisco router, when will the router actually reserve the bandwidth for the MPLS traffic engineering tunnel?
A. during the autoroute process
B. during constraint-based routing calculations
C. on the receipt of the RSVP Path message
D. on the receipt of the RSVP Resv message

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 40
Cisco MPLS TE path setup can be affected by which three tunnel attributes? (Choose three.)
A. bandwidth
B. delay
C. MTU
D. priority
E. affinity

Correct Answer: ADE Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 41
When using the tunnel mpls traffic-eng path-option 1 explicit name test command in Cisco MPLS TE tunnel configurations, the test explicit-path configuration will consist of a list of which values?
A. tunnel endpoint
B. resource class affinity
C. MPLS label
D. IP address

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 42
Cisco MPLS TE resource attributes that are configured locally for each link are distributed to the headend router of the traffic engineering tunnel using which protocol?
A. BGP
B. MP-BGP
C. LDP
D. RSVP
E. OSPF or IS-IS with TE extension

Correct Answer: E Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 43
When implementing Cisco MPLS TE, the constrained-based path calculations will use which value as the TE cost of each link within the MPLS domain?
A. By default, it will use the IGP metric, or each link can be assigned a specific value using the admin-weight command.
B. It can only use the IGP metric as the TE cost.
C. It will use the interface bandwidth as the TE cost.
D. Each link must be assigned a TE cost using the metric command.

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 44
Which affinity and mask value will match the link affinity that has 0x0F in the first 8 bits and 0x01 in the last 8 bits, and the middle 16 bits can be any value?
A. affinity 0x0F000001 mask 0x0F000001
B. affinity 0x0F000001 mask 0x00000000
C. affinity 0x0F000001 mask 0x11111111
D. affinity 0x0F000001 mask 0x11000011
E. affinity 0x0F000001 mask 0xFF0000FF
F. affinity 0x0F000001 mask 0x00FFFF00

Correct Answer: E Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 45
Which two features are used to provide Cisco MPLS TE node and link protection? (Choose two.)
A. autoroute
B. fast reroute
C. backup tunnels
D. BFD

Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 46
In Cisco MPLS TE implementations, what can cause the tunnel bandwidth to adjust automatically based on the traffic load in the tunnel?
A. fast reroute
B. admin weight
C. autobandwidth
D. bandwidth subpool

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 47
Which affinity value will be matched by the affinity bit mask of the affinity 0xFF00000A mask 0xFFFF000F command?
A. 0xFFFF000A
B. 0xFF00EEEA
C. 0xFF000000
D. 0x00000000
E. 0x11110001

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 48
Refer to the Cisco IOS XR configuration exhibit.

Which statement is correct?
A. The backup tunnel-te 10 tunnel is using the highest setup and hold priority settings of 7.
B. The backup tunnel path is learned dynamically.
C. The fast-reroute command is missing under the (config-mpls-te-if)# configuration mode.
D. Interface gi0/0/0/10 is the protected link.

Correct Answer: D Section: (none)
Explanation
Explanation/Reference:
Explanation:
QUESTION 49
When defining an explicit MPLS TE tunnel path, which two command options are available under the explicit-path configuration mode? (Choose two.)
A. exclude-address
B. include-address
C. next-address
D. dynamic-address

Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 50
Which three mechanisms are used to implement MPLS TE? (Choose three.)
A. tunnel interface
B. CSPF
C. RSVP
D. LDP
E. MP-BGP

Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 51
Implementing IPoDWDM interfaces on Cisco CRS routers eliminates the need for which network component?
A. ROADM
B. external transponders
C. electrical-optical-electrical converters
D. electrical cross-connect

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 52
Layer 2 VPN services that are offered by traditional service providers using a SONET/SDH backbone can be implemented by service providers using an IP/MPLS backbone with which MPLS feature?
A. LSP stitching
B. AToM
C. virtual private WAN services
D. cell-mode MPLS

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 53
On Cisco routers, which QoS marker is only locally significant?
A. DSCP
B. MPLS EXP
C. IP precedence
D. QoS group
E. discard eligible (DE)

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 54
Which QoS mechanism is used for congestion avoidance?
A. LLQ
B. CBWFQ
C. WRED
D. LFI
E. traffic policing

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 55
Only based on the Cisco IOS XR policy-map configuration exhibit,

which statement is correct?
A. All DSCP AF41 marked packets will be dropped when the average queue length reaches 12,000 packets.
B. DSCP AF11 marked packets will be randomly dropped when the average queue length reaches 10,000 packets.
C. DSCP AF11 and AF41 marked packets are guaranteed a minimum bandwidth of 1 Mb/s.
D. DSCP AF11 and AF41 marked packets are guaranteed a maximum bandwidth of 1 Mb/s.

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 56
Referring to the show output exhibit,

which statement is correct?
A. The P1 router is receiving label information for the 10.0.2.1/32 prefix from two LDP peers.
B. The P1 router is receiving label information for the 10.7.1.1/32 prefix from two LDP peers.
C. The P1 router is using the IMP-NULL local label for the 10.7.1.1/32 prefix because 10.7.1.1/32 is the loopback interface IP address on the P1 router.
D. The P1 router will perform PHP for the 10.7.1.1/32 and 10.7.10.1./32 prefixes.

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 57
Referring to the traceroute output exhibit that is shown, which statement is correct?

A. There is no problem with the end-to-end LSP as indicated by the successful trace.
B. Normal PHP operation is performed by the hop 4 router.
C. The end-to-end LSP is broken at hop 4.
D. At each hop, each LSR is able to perform label swapping.

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 58
What is an important requirement with MPLS applications like Layer 3 MPLS VPNs?
A. All the PE routers loopback addresses should be summarized to reduce the number of routing table entries in the core routers.
B. Targeted hellos are required between all the PE routers.
C. An end-to-end LSP is required between the PE routers.
D. The LSPs that are built between the PE routers must be symmetrical (bidirectional).

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 59
When implementing MPLS TE tunnels on Cisco IOS XR routers, what is the tunnel setup and hold priority value range, and which value has the highest priority?
A. 0-63, where 0 is the highest priority
B. 0-63, where 63 is the highest priority
C. 0-7, where 0 is the highest priority
D. 0-7, where 7 is the highest priority

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 60
Which Cisco IOS XR command should be used in order to enable LDP on all interfaces for which the IGP protocol is enabled?
A. RP/0/0/CPU0:R1(config-ospf)#mpls ldp auto-config
B. RP/0/0/CPU0:R1(config-ospf)#mpls ldp interface all enable
C. RP/0/0/CPU0:R1(config-ospf)#enable all
D. RP/0/0/CPU0:R1(config-ldp)#enable all

Correct Answer: A Section: (none) Explanation Explanation/Reference:
Explanation:
QUESTION 61
Refer to the partial Cisco IOS XR configurations exhibit for Router 1 and Router 2.

There are two routers that are connected back to back over the Gigabit Ethernet link. If the “show mpls ldp neighbor” command output on Router 1 does not show LDP peering with Router 2, what could be the possible root cause of the LDP peering problem?
A. missing interface under OSPF IGP configuration
B. hello timers mismatch on Router 1 and Router 2
C. password for LDP session mismatch on Router 1 and Router 2
D. MPLS LDP session protection is not configured

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 62
Which Cisco IOS XR command should be used to identify if MPLS TE FRR is enabled?
A. show mpls traffic-eng tunnel <tunnel#>
B. show mpls frr
C. show mpls traffic-eng protection
D. show mpls protection
E. show mpls fast-reroute

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 63
When a link flaps, an mpls ldp session will also flap. Which feature minimizes traffic loss and provides faster convergence after the link is re-established?
A. BFD
B. MPLS LDP IGP SYNC
C. graceful restart
D. LDP session protection
E. LDP nonstop routing

Correct Answer: D Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 64
A DSCP value of 41 in decimal corresponds to which IP precedence value?
A. 3 ?Flash
B. 4 ?Flash Override
C. 5 ?Critical
D. 6 ?Internet Control
E. 7 ?Network Control

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
Explanation:
QUESTION 65
DRAG DROP A.

B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: RSVP PATH Message — sent from the tunnel headend to the tunnel tailend —- carried the MPLS label requests RSVP RESV Message–Sent from the tunnel tailend to the tunnel headend — carries the MPLS lables
QUESTION 66
DRAG DROP A.

B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: Can drop express traffic beyond the committed rate and remark non coming traffic before transmitting it–traffic policing Use to avoid the TCP global synchronization problems that occur when tail drop is used as the congestion avoidance mechanism—WRED Provide a strict priority queue to allow delay-sensitive data such as voice t be dequeued and sent first–CBWFQ Express traffic beyond the committed rate will be queue and scheduled for later transmission .Only applied in the output directions.–traffic shaping
QUESTION 67
DRAG DROP A.

B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: Applies the QOS policy to interface–service policy Defines the PHB qos action for each of the different traffic classes–policy map Defines the making parameters for classifying packets into service classes–class-map
QUESTION 68
DRAG DROP

A.
B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: 1)Build RIB 2) Assign labels 3) Advertise Labels 4)Build LFIB
QUESTION 69
DRAG DROP

A.
B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: All network packets are treated exactly the same–Best Effort It divides traffic classes and applies a different level of service for each class–Diffserv Traffic-handling characteristics are based on signaling events from network-based applications– intServ
QUESTION 70
DRAG DROP

A.
B.
C.
D.

Correct Answer: Section: (none) Explanation
Explanation/Reference:

Explanation: If a qos making (MPLS EXP) is changed in the MPLS network, it is also changed in the egress IP Packet–short-pipe mode This provide QOS transparency where the customer QOS marking (for example,DSCP) in the IP Packet is preserved.The egress PE uses the original customer QOS marking instead of the service provider QOS marking–pipe mode Qos is done on the output interface of the PE router that is based on the receive —–Uniform mode
QUESTION 71
Scenario:
On the PE8-router what is the label value used to reach the 10.7.1.1/32 network prefix?
A. 10.0.2.1:0
B. imp-null
C. 16024
D. 128
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
Explanation: Need to run command at PE8 router so that we can get the value .Local tag value is answer for these #show mpls forwarding-table 10.7.1.1
QUESTION 72
Scenario:

On P2IOS-XR router what is targeted LDP hellos hold time on LDP session with 10.0.1.1:0 LDP ID?
A. 90 sec
B. 10 sec
C. 3 sec
D. 8.6 sec

Correct Answer: B Section: (none) Explanation
Explanation/Reference:
Explanation: Need to run command at PE8 router so that we can get the value . #show mpls ldp parameters # show mpls ldp neighbor detail
QUESTION 73
Scenario:

From PE8 router, what is the label action used to reach the P2 loopback 0 interface 10.0.2.1/32?
A. Swap label 35 with label 16004
B. Push label 16004
C. Pop label 35 D. Pop label 16009
E. Push Label 16009
F. Swap label 35 with label 16009

Correct Answer: E Section: (none) Explanation
Explanation/Reference:
Explanation: Need to run command at PE8 router so that we can get the value .Local tag value is answer for these #show mpls forwarding-table 10.0.2.1

Cisco 642-887 Questions & Answers with explanations is all what you surely want to have before taking Cisco 642-887 exam.Cisco Cisco 642-887 Interactive Testing Engine is ready to help you to get your Cisco 642-887 by saving your time by preparing you quickly for the Cisco exam. If you are worried about getting your Cisco 642-887 certification passed and are in search of some best and useful material,Cisco 642-887 Q&A will surely serve you to enhance your Interconnecting Cisco Networking Devices study.