100% valid Cisco300-320 brain dumps with more new added questions.By training the Cisco300-320 questions, you will save a lot time in preparing the exam.Visit www.Flydumps.com to get the 100% pass ensure!
QUESTION 5
5) Client 1 is not able to ping the server
Situation 5: Unable to ping R4 fast ethernet port from DSW1 and check ip eigrp neighbors from
DSW1 u willnot c R4 as neighbor.(use ipv4 Layer 3)
A. R4
B. IP4 EIGRP
C. Change eigrp process no: from 1 tp 10 on R4 according to the configuration on DSW1 and DSW2
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: DSW1 can ping 10.1.4.5 >>> connected route DSW1 can’t ping 10.1.4.9 interface of R4>>> because of wrong EIGRP process number
QUESTION 6
6) Client 1 is not able to ping the server
A. R4
B. route redistribution
C. change the name of the route-map under the router EIGRP process from “EIGRP_to_OSPF” to ”EIGRP->OSPF”
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: R4(config)# router eigrp 10 R4(config-router)#redistribute ospf 1 route-map EIGRP_to_OSPF
BUT route-map was named: route-map EIGRP->OSPF R4 has route map to redistribute between EIGRP and OSPF…but in the name of the route map under EIGRP redistribution does no match the name of the route map so the answer is to delete the redistribution command under EIGRP (the one with the wrong route map name) and replace it with the redistribution command with the right route map name.
QUESTION 7 7) Client 1 is not able to ping the server
Situation 7: client is unable to ping R1’s serial interface from the client. Check where authentication is not given under router ospf of one of the routers ( R1 or R2). (use ipv4 Layer 3)
A. R1
B. ipv4 OSPF
C. ip ospf authentication message-digest command must be given on s0/0/0
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
client cannot ping R1’s interface s0/0/0 ip address 10.1.1.1
QUESTION 8 8) Client 1 is not able to ping the server
Situation 8: client is not able to ping the web server, but the routers can ping the server. NAT problem. (use ipv4 Layer 3)
A. R1
B. IPV4 NAT
C. under NAT access list, enter the command permit 10.2.0.0 0.0.255.255
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 9
9) Client 1 is not able to ping the server
A. R1
B. BGP
C. delete the wrong neighbor statement and enter the correct neighbor address in the neighbor command (change 209.56.200.226 to 209.65.200.226)
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference:
QUESTION 10 10) Client 1 is not able to ping the server
Situation 10: client is not able to ping the server. Except for R1, no one else can ping the server. BGP routes have not been redistributed into OSPF. (use ipv4 Layer 3)
A. R1
B. IPv4 Security
C. Add permit 209.65.200.224 0.0.0.3 to R1’s ACL.
Correct Answer: ABC
Section: (none)
Explanation
Explanation/Reference:
QUESTION 11
11) IPV6 loopback of R2 cannot be pinged from DSW1’s loopback.
Situation 11: ipv6 ospf was not enabled on R2’s serial interface connecting to R3. (use ipv6 Layer
3)
A. R2
B. IPV6 OSPF
C. on the serial interface of R2, enter the command, ipv6 ospf 6 area 12 (or area 0, check the IPV6 topology.)
Correct Answer: ABC
Section: (none)
Explanation
Explanation/Reference:
R2 can’t establish neighborship relation with R1 because it dose not have any interfaces in Area
12.
QUESTION 12
12) HSRP: DSW1 does not become active.
Situation 12: under the standby configuration of DSW1, the command standby 10 track 1
decrement 60 is given, this has to be changed to track 10. (use ipv4 Layer 3)
A. DSW1
B. HSRP
C. delete the command with track 1 and enter the command with track 10.
Correct Answer: ABC Section: (none) Explanation
Explanation/Reference: HSRP not active for the VLAN 10 but the ping was working through DSW2. DSW1: track 1 ip route 10.1.1.1 255.255.255.0 metric threshold threshold metric up 1 down 2 ! track 10 ip route 11.11.11.11 255.255.255.0 metric threshold threshold metric up 61 down 62
interface Vlan10 ip address 10.2.1.1 255.255.255.0 standby 10 ip 10.2.1.254 standby 10 priority 200 standby 10 preempt standby 10 track 1 decrement 60
Answer: on DSW1 in interface vlan 10 config mode run: no standby 10 track 1 decrement 60 standby 10 track 10 decrement 60
IP addresses for track command not exact for the real exam!!!!
Acquiring Cisco300-320 certifications are becoming a huge task in the field of I.T. More over these exams like Cisco300-320 exam are now continuously updating and accepting this challenge is itself a task.This Cisco300-320 practice test is an important part of Microsoft certifications and at Cisco300-320 certification Flydumps we have the resources to prepare you for this.The Cisco300-320 exam is essential and core part of Cisco300-320 certifications and once you clear the exam you will be able to solve the real time problems yourself.